Schutzhund A-Frame

Drogon

Hot Topics Subscriber
I'm going to be building a Schutzhund A-Frame and would really like to make it more portable than an average one. I'm considering using NDS Tufftrack Gravel - Grass Pavers 2' x 2' ( NDS Tufftrack Gravel - Grass Pavers 2' x 2' ) instead of wood. I'd have to put something over it. I'm not sure if the 'AstroTurf' would be enough. I think I'd likely have to put a thin piece of wood and then the AstroTurf. I know these pavers are strong, I've seen cement trucks drive over them when they're laid flat on the grass. I'm not sure how well they would hold up in the air for the A-Frame. I'm not certain how well those clips would remain clipped. I'd likely glue them and suppose I could reinforce the sections by drilling a hole and putting in a nut and bolt.


Opinions?
 
I have no experience with those panels,but they seem strong.
I question their torsional rigidity when upright though?
On the ground they support the weight,upright though?

A thin wood like Formica may increase the rigidity?
Another thought,fill the cells with foam;)
 
Another thought,fill the cells with foam
I was thinking the same thing.

I'm also concerned about getting the correct size. 2 foot squares means I'll have to cut some and possibly leave some edges that could cause a problem.
 
I was thinking the same thing.

I'm also concerned about getting the correct size. 2 foot squares means I'll have to cut some and possibly leave some edges that could cause a problem.
You'll definitely have to trim some edges,side by side panels the edges aren't flush.
Have a Dremel tool?
If so you should be good to go,if not pick one up.They're great for trimming dog nails too so no worry of buying a tool you won't use again.:thumbsup2:
 
A thin wood like Formica may increase the rigidity?
Another thought,fill the cells with foam;)
Maybe I could have one of those companies that spray foam into attics fill it full for me. Then maybe I could have it sprayed with pickup truck bed-liner stuff.
 
Maybe I could have one of those companies that spray foam into attics fill it full for me. Then maybe I could have it sprayed with pickup truck bed-liner stuff.
I like the bed liner idea,I would imagine it would hold up better long term vs AstroTurf.
On the foam,I guess it's worth inquiring for a quote.
If they're insane on the pricing its time for you to take off the IT hat and put on your fabricators hat. :D

Hits home improvement store for some thick mill plastic,do t get the thin painters plastic,and pick up a couple cans of this.
image.webp

Here's how I would tackle this.
Back that beautiful new Ford out of the garage so you can use the floor as a flat surface.
Tape down the plastic.
Wax the plastic with carnauba car wax.
Place your panels on the plastic.
Secure them with weights in a few places to hold firm to the floor/plastic.
Fill the cells.
Move your weights around to fill the cells covered by the weights.
It will probably expand beyond the top of the cell panels but that's ok,because your working the back side of the panels.
Once dry pick them up and pull the plastic,that surface should be flat because you used the floor and plastic as part of your form.
 
I like the bed liner idea,I would imagine it would hold up better long term vs AstroTurf.
On the foam,I guess it's worth inquiring for a quote.
If they're insane on the pricing its time for you to take off the IT hat and put on your fabricators hat. :D

Hits home improvement store for some thick mill plastic,do t get the thin painters plastic,and pick up a couple cans of this.
View attachment 62865

Here's how I would tackle this.
Back that beautiful new Ford out of the garage so you can use the floor as a flat surface.
Tape down the plastic.
Wax the plastic with carnauba car wax.
Place your panels on the plastic.
Secure them with weights in a few places to hold firm to the floor/plastic.
Fill the cells.
Move your weights around to fill the cells covered by the weights.
It will probably expand beyond the top of the cell panels but that's ok,because your working the back side of the panels.
Once dry pick them up and pull the plastic,that surface should be flat because you used the floor and plastic as part of your form.
I had pretty much the same idea. I was thinking wax paper. I figured it would only take a couple minutes for someone to spray the entire thing vs a couple of hours for me to fill it up with that 'Great Stuff'.

Not sure how I would hinge it or how I would attach the 3 slats.
 
I had pretty much the same idea. I was thinking wax paper. I figured it would only take a couple minutes for someone to spray the entire thing vs a couple of hours for me to fill it up with that 'Great Stuff'.

Not sure how I would hinge it or how I would attach the 3 slats.
Wax paper is a good idea,seams between sheets might leak a little but probably easier on the wallet.
Those clips would probably be fine after the foam locks them in,but then,you wanted easy transport.
For hinges? Door hinges maybe?
Carriage bolts with rounded heads so the dog doesn't catch a toe or something.Washers and wing nuts on the underside.
 

Back
Top