Material for bed

CalamitysHuckleberry

Notable member
I'm going to make two of these beds for HuckLamity or CalBerry which ever one you prefer. These are going to be for outside.

View: http://youtu.be/PG3pNLApteY


I'm curious if y'all think a piece of hammock would work?

My local box hardware store has the hammock that you tie to a try for $15. It holds 175 pounds. I'm thinking I could cut that in half and use it. I just don't know if cutting it would compromise the strength integrity of it.

Any suggestions?
 
Can't wait to see how it turns out!
Ditto! I think you can get some breathable outdoor resistant material, which is most likely what you're looking at so it should work great.
 
That sounds like a neat project. I have thought about it just never acted on it. Keep us posted how it works out. I always thought that velcro instead of sewing would make it easier to wash. Never set down and actually tried to figure out the mechanics of making it glued together so it would be sturdy and yet able to change or wash the bedding.
 
I think these are made to just be hosed off. They use awning type of material and they are attached to the PVC with screws. Sounds like easy maintenance.

I will keep you posted, since the snow is gone now!
 
I do see how screwing it down permanent would solve some problems - but if the material tears or needs to be replaced seems like you would not be able to reuse the frame because of the screws and probably not being able to reuse the same holes. But they sure do allow you to make a very tight bed.

i bought a childs cot and my dogs love it. They have not destroyed it yet and I have had it for a couple years now. Even the puppies love it and no one has eaten it.
 
I do see how screwing it down permanent would solve some problems - but if the material tears or needs to be replaced seems like you would not be able to reuse the frame because of the screws and probably not being able to reuse the same holes. But they sure do allow you to make a very tight bed.

i bought a childs cot and my dogs love it. They have not destroyed it yet and I have had it for a couple years now. Even the puppies love it and no one has eaten it.

I think as you do that the frame can't be reused. I will have to if the cost outweighs it. That's why I wanted a good material.

The child's cot is a excellent idea, can you just hose it off?
 
Ya know they sell Coolaro covers for $12.00 Amazon.com: coolaroo replacement cover Might fit your set-up

I think it's wonderful that your making your own.....I purchased 5 Large coolaro beds 3 years ago for $20.00 each (I buy in the winter, when they are cheaper)....I have only had to change one cover thus far (puppy antics) and three of them are outside in all kinds of weather - my dogs love the raised beds in the summer.
 
Ya know they sell Coolaro covers for $12.00 Amazon.com: coolaroo replacement cover Might fit your set-up

I think it's wonderful that your making your own.....I purchased 5 Large coolaro beds 3 years ago for $20.00 each (I buy in the winter, when they are cheaper)....I have only had to change one cover thus far (puppy antics) and three of them are outside in all kinds of weather - my dogs love the raised beds in the summer.
Dang it!! I just did an order with Amazon and needed to spend $10 to get free shipping!
 
Did you ever make any of these? If so, what do you think of them?

Thanks!
 
I'm going to make two of these beds for HuckLamity or CalBerry which ever one you prefer. These are going to be for outside.

View: http://youtu.be/PG3pNLApteY


I'm curious if y'all think a piece of hammock would work?

My local box hardware store has the hammock that you tie to a try for $15. It holds 175 pounds. I'm thinking I could cut that in half and use it. I just don't know if cutting it would compromise the strength integrity of it.

Any suggestions?

I think most of them use duck cloth from Jo-Ann's (same fabric they use on the corn hole bags). I don't think the strength would be compromised if you seemed the edges with a sewing machine. If you don't have an industrial one you would need to reinforce the stitching.

I made my beds from wood and then made a mattress to put on top. When these wear out I plan on making/buying the PVC ones. Much easier to wash!
 

Back
Top